Guide
Nominal vs actual lumber sizes
A 2×4 is not 2 inches by 4 inches. It is 1.5 × 3.5. The name is the size the board was when it was cut rough; the size you take home is smaller — and knowing which number to use where is the difference between a tally that matches the supplier and a joint that fits.
Why the sizes differ
Boards are sawn rough to the nominal size, then dried and planed smooth (surfaced) on all four sides. Drying shrinks the wood and surfacing removes material, so the finished board is thinner and narrower than its name. The name stuck — the trade still calls the board by its rough size — while the actual size is what your tape measure reads. Lengths, by contrast, are generally as stated: an 8 ft board is 8 ft long, sometimes a fraction over, to allow trimming square.
The surfacing loss follows a pattern you can read off the table: boards 1 in nominal lose ¼ in of thickness; boards 2 in nominal and up lose ½ in. Widths lose ½ in up to 6 in nominal, then ¾ in above that. That is why a 1×6 is 0.75 × 5.5 in while a 2×12 is 1.5 × 11.25 in.
The dressed-size table
Standard dressed (surfaced-dry) sizes for North American softwood lumber. Thickness is listed first in the nominal name; actual sizes are in inches.
| Nominal | Actual | Nominal | Actual |
|---|---|---|---|
| 1 × 2 | 0.75 × 1.5 | 2 × 2 | 1.5 × 1.5 |
| 1 × 3 | 0.75 × 2.5 | 2 × 3 | 1.5 × 2.5 |
| 1 × 4 | 0.75 × 3.5 | 2 × 4 | 1.5 × 3.5 |
| 1 × 5 | 0.75 × 4.5 | 2 × 5 | 1.5 × 4.5 |
| 1 × 6 | 0.75 × 5.5 | 2 × 6 | 1.5 × 5.5 |
| 1 × 8 | 0.75 × 7.25 | 2 × 8 | 1.5 × 7.25 |
| 1 × 10 | 0.75 × 9.25 | 2 × 10 | 1.5 × 9.25 |
| 1 × 12 | 0.75 × 11.25 | 2 × 12 | 1.5 × 11.25 |
| 4 × 4 | 3.5 × 3.5 | 4 × 6 | 3.5 × 5.5 |
| 6 × 6 | 5.5 × 5.5 |
Rough-sawn lumber, green lumber, and hardwood sold in the rough follow different conventions — measure the actual piece, and ask your supplier how they tally. The table above is the dressed softwood standard (Western Wood Products Association sizes, as stocked by suppliers).
What it means for your tally
The tally uses nominal sizes. Suppliers count board feet on the name, not the tape measure. An 8 ft 2×4 is tallied as:
96 × 4 × 2 ÷ 144 = 5.33 board feet
Computed from the actual size instead, the same board would give 96 × 3.5 × 1.5 ÷ 144 = 3.5 board feet — a number no supplier will recognize, and a price that will not match the invoice. That is a 34% difference on the same board. Never compute the tally from dressed sizes.
The fit uses actual sizes. A gap that must hold a 2×4 needs 3.5 inches of room, not 4. A shelf span, a mortise, a hole for a post — all follow the tape measure. Design to actual, order to nominal.
The calculators on this site follow the same rule: presets enter nominal sizes, and the deck board calculator asks you to enter the width your supplier counts.
Designing with actual sizes
Joinery, housings, shelf spans, and anything that must fit must be designed around actual measurements — ideally measurements you took yourself, from the boards in your hands, with a tape or calipers. Nominal sizes are for ordering and tallying; actual sizes are for building. When a plan says “2×4”, read it as “the board sold as a 2×4, measuring 1.5 × 3.5 in” and check the plan’s dimensions against that reality before cutting.
One habit prevents most fit errors: measure the boards you bought before you cut the pieces they must fit into. Boards vary slightly even within one bundle, and a housing cut to the table size rather than the measured size is a housing cut twice.
Hardwood thickness in quarters
Hardwood is often quoted in quarters of an inch in the rough: 4/4 means roughly 1 inch thick, 8/4 roughly 2 inches. Surfaced hardwood is thinner than its quarter figure. Because hardwood tallying varies by supplier, confirm the basis before you compare prices — and never assume a quarter figure equals a finished thickness. If a quote uses quarters, confirm the surfaced thickness you will actually receive before designing joinery around it, and confirm whether the tally uses the quarter thickness or the surfaced one.
Questions, answered
What is the actual size of a 2×4?
1.5 × 3.5 inches. The 2×4 name is the rough-sawn nominal size; drying and surfacing reduce it.
Do I use nominal or actual sizes for board feet?
Nominal, for the tally — suppliers count board feet on the name. Use actual sizes for anything that must fit.
What does 4/4 mean in hardwood?
Roughly 1 inch thick in the rough. Surfaced 4/4 ends up under a full inch; confirm the surfaced thickness and the tally basis with the supplier.
Size table and worked numbers last checked 18 November 2026. See the changelog.